Mirage Recalls

Mitsubishi Motors Recalls

Last Update: August 27, 2004


NHTSA Recall ID: 01V340001

Mitsubishi MIRAGE 2001 (01)

Mitsubishi Recall Campaign No.:

Component: ENGINE AND ENGINE COOLING:ENGINE

Recall Date (Y/M):2001/11

Defect: VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE BOLT SECURING THE CRANKSHAFT PULLEY CAN BECOME LOOSE AND THE PULLEY COULD FALL OFF THE VEHICLE.

Consequence: THE CONDITION CAN RESULT IN A LOSS OF POWER STEERING ASSIST, INCREASING THE RISK OF A CRASH.

Corrective Action: DEALERS WILL INSPECT THE VEHICLES TO INSURE THAT THE BOLT IS TIGHTENED. FOR THOSE BOLTS NOT PROPERLY TIGHTENED, THE BOLT AND PULLEY WILL BE REMOVED AND INSPECTED FOR ANY INDICATION OF DAMAGE. COMPONENTS SHOWING ANY SIGNS OF DAMAGE WILL BE REPLACED AND THE BOLT TIGHTENED TO THE PROPER TORQUE. OWNER NOTIFICATION BEGAN NOVEMBER 26, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT MITSUBISHI AMERICA AT 1-888-648-7820.


NHTSA Recall ID: 01V340001

Mitsubishi MIRAGE 2000 (00)

Mitsubishi Recall Campaign No.:

Component: ENGINE AND ENGINE COOLING:ENGINE

Recall Date (Y/M):2001/11

Defect: VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE BOLT SECURING THE CRANKSHAFT PULLEY CAN BECOME LOOSE AND THE PULLEY COULD FALL OFF THE VEHICLE.

Consequence: THE CONDITION CAN RESULT IN A LOSS OF POWER STEERING ASSIST, INCREASING THE RISK OF A CRASH.

Corrective Action: DEALERS WILL INSPECT THE VEHICLES TO INSURE THAT THE BOLT IS TIGHTENED. FOR THOSE BOLTS NOT PROPERLY TIGHTENED, THE BOLT AND PULLEY WILL BE REMOVED AND INSPECTED FOR ANY INDICATION OF DAMAGE. COMPONENTS SHOWING ANY SIGNS OF DAMAGE WILL BE REPLACED AND THE BOLT TIGHTENED TO THE PROPER TORQUE. OWNER NOTIFICATION BEGAN NOVEMBER 26, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT MITSUBISHI AMERICA AT 1-888-648-7820.


NHTSA Recall ID: 01V340001

Mitsubishi MIRAGE 1999 (99)

Mitsubishi Recall Campaign No.:

Component: ENGINE AND ENGINE COOLING:ENGINE

Recall Date (Y/M):2001/11

Defect: VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE BOLT SECURING THE CRANKSHAFT PULLEY CAN BECOME LOOSE AND THE PULLEY COULD FALL OFF THE VEHICLE.

Consequence: THE CONDITION CAN RESULT IN A LOSS OF POWER STEERING ASSIST, INCREASING THE RISK OF A CRASH.

Corrective Action: DEALERS WILL INSPECT THE VEHICLES TO INSURE THAT THE BOLT IS TIGHTENED. FOR THOSE BOLTS NOT PROPERLY TIGHTENED, THE BOLT AND PULLEY WILL BE REMOVED AND INSPECTED FOR ANY INDICATION OF DAMAGE. COMPONENTS SHOWING ANY SIGNS OF DAMAGE WILL BE REPLACED AND THE BOLT TIGHTENED TO THE PROPER TORQUE. OWNER NOTIFICATION BEGAN NOVEMBER 26, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT MITSUBISHI AMERICA AT 1-888-648-7820.


NHTSA Recall ID: 00V311001

Mitsubishi MIRAGE 1999 (99)

Mitsubishi Recall Campaign No.:

Component: ENGINE AND ENGINE COOLING:ENGINE

Recall Date (Y/M):2000/10

Defect: VEHICLE DESCRIPTION: PASSENGER VEHICLES: MIRAGE MODEL VEHICLES EQUIPPED WITH 1.5L ENGINES; MONTERO SPORT MODELS EQUIPPED WITH 3.0L ENGINES; AND MONTERO MODELS EQUIPPED WITH 3.0L ENGINES. THE BOLT SECURING THE CRANKSHAFT PULLEY CAN BECOME LOOSE AND THE PULLEY COULD FALL OFF THE VEHICLE.

Consequence: THE CONDITION CAN RESULT IN A LOSS OF POWER STEERING ASSIST, INCREASING THE RISK OF A CRASH.

Corrective Action: ON THE MIRAGE VEHICLES, THE DEALERS WILL INSTALL A NEW, IMPROVED CRANKSHAFT PULLEY BOLT ON THE OLDER ENGINES. ON NEW ENGINES WHICH ALREADY HAVE THE IMPROVED BOLT, THE DEALER WILL TIGHTEN THE CRANKSHAFT PULLEY BOLT TO THE CORRECT TORQUE SPECIFICATION. ON THE MONTERO MODELS, DEALERS WILL TIGHTEN THE CRANKSHAFT PULLEY BOLT TO THE CORRECT TORQUE SPECIFICATIONS. IF THE BOLT IS DAMAGED, IT WILL BE REPLACED.


NHTSA Recall ID: 00V311001

Mitsubishi MIRAGE 1998 (98)

Mitsubishi Recall Campaign No.:

Component: ENGINE AND ENGINE COOLING:ENGINE

Recall Date (Y/M):2000/10

Defect: VEHICLE DESCRIPTION: PASSENGER VEHICLES: MIRAGE MODEL VEHICLES EQUIPPED WITH 1.5L ENGINES; MONTERO SPORT MODELS EQUIPPED WITH 3.0L ENGINES; AND MONTERO MODELS EQUIPPED WITH 3.0L ENGINES. THE BOLT SECURING THE CRANKSHAFT PULLEY CAN BECOME LOOSE AND THE PULLEY COULD FALL OFF THE VEHICLE.

Consequence: THE CONDITION CAN RESULT IN A LOSS OF POWER STEERING ASSIST, INCREASING THE RISK OF A CRASH.

Corrective Action: ON THE MIRAGE VEHICLES, THE DEALERS WILL INSTALL A NEW, IMPROVED CRANKSHAFT PULLEY BOLT ON THE OLDER ENGINES. ON NEW ENGINES WHICH ALREADY HAVE THE IMPROVED BOLT, THE DEALER WILL TIGHTEN THE CRANKSHAFT PULLEY BOLT TO THE CORRECT TORQUE SPECIFICATION. ON THE MONTERO MODELS, DEALERS WILL TIGHTEN THE CRANKSHAFT PULLEY BOLT TO THE CORRECT TORQUE SPECIFICATIONS. IF THE BOLT IS DAMAGED, IT WILL BE REPLACED.


NHTSA Recall ID: 97V179000

Mitsubishi MIRAGE 1998 (98)

Mitsubishi Recall Campaign No.:

Component: SERVICE BRAKES, HYDRAULIC:POWER ASSIST:VACUUM:HOSES, LINES/PIPING, AND FITTINGS

Recall Date (Y/M):1997/10

Defect: VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES MAY HAVE A POORLY MANUFACTURED VACUUM CHECK VALVE IN THE VACUUM HOSE BETWEEN THE INTAKE MANIFOLD AND THE BRAKE VACUUM BOOSTER. WHEN THE BRAKE PEDAL IS DEPRESSED, THE VACUUM BOOSTER CHECK VALVE CAN STICK TO THE VALVE BODY.

Consequence: THIS CONDITION WOULD RESULT IN REDUCTION OR LOSS OF VACUUM BOOST, REDUCING BRAKE EFFICIENCY.

Corrective Action: DEALERS WILL REPLACE THE BRAKE VACUUM HOSE.


NHTSA Recall ID: 00V311001

Mitsubishi MIRAGE 1997 (97)

Mitsubishi Recall Campaign No.:

Component: ENGINE AND ENGINE COOLING:ENGINE

Recall Date (Y/M):2000/10

Defect: VEHICLE DESCRIPTION: PASSENGER VEHICLES: MIRAGE MODEL VEHICLES EQUIPPED WITH 1.5L ENGINES; MONTERO SPORT MODELS EQUIPPED WITH 3.0L ENGINES; AND MONTERO MODELS EQUIPPED WITH 3.0L ENGINES. THE BOLT SECURING THE CRANKSHAFT PULLEY CAN BECOME LOOSE AND THE PULLEY COULD FALL OFF THE VEHICLE.

Consequence: THE CONDITION CAN RESULT IN A LOSS OF POWER STEERING ASSIST, INCREASING THE RISK OF A CRASH.

Corrective Action: ON THE MIRAGE VEHICLES, THE DEALERS WILL INSTALL A NEW, IMPROVED CRANKSHAFT PULLEY BOLT ON THE OLDER ENGINES. ON NEW ENGINES WHICH ALREADY HAVE THE IMPROVED BOLT, THE DEALER WILL TIGHTEN THE CRANKSHAFT PULLEY BOLT TO THE CORRECT TORQUE SPECIFICATION. ON THE MONTERO MODELS, DEALERS WILL TIGHTEN THE CRANKSHAFT PULLEY BOLT TO THE CORRECT TORQUE SPECIFICATIONS. IF THE BOLT IS DAMAGED, IT WILL BE REPLACED.


NHTSA Recall ID: 97V073001

Mitsubishi MIRAGE 1993 (93)

Mitsubishi Recall Campaign No.:

Component: SEAT BELTS:FRONT:ANCHORAGE

Recall Date (Y/M):1997/05

Defect: THE GUIDE RAIL ON THE DRIVER'S SIDE CONTAINS A COVERED CABLE AND ALSO AN ANGLED BELT GUIDE AT THE TOP END OF THE WEBBING. THE COMBINATION OF THESE FACTORS CAN LEAD, OVER TIME, TO THE CABLE'S MOVEMENT EXERTING ABRADING FORCE TO THE LOWER EDGES OF THE CABLE'S CHAMBER, SUFFICIENT TO CAUSE THE CABLE TO DROP OUT OF THE CHAMBER WITH THE SHOULDER BELT ANCHORAGE BECOMING STUCK.

Consequence: IN THE EVENT OF A CRASH, THE SEAT OCCUPANT MAY NOT BE PROPERLY RESTRAINED.

Corrective Action: DEALERS WILL INSTALL A NEW REPLACEMENT GUIDE RAIL.


NHTSA Recall ID: 97V063001

Mitsubishi MIRAGE 1993 (93)

Mitsubishi Recall Campaign No.:

Component: LATCHES/LOCKS/LINKAGES:DOORS:LATCH

Recall Date (Y/M):1997/05

Defect: EXCESS LUBRICATION CAN CAUSE THE RUBBER DOOR LATCH SWITCH COVER TO DEFORM, AND THE DOOR LATCH SWITCH TO MALFUNCTION, SO THAT THE SHOULDER BELT ANCHORAGE WOULD REMAIN AT THE A-PILLAR WHEN THE DOOR WAS CLOSED.

Consequence: IN THE EVENT OF A CRASH, THE SEAT OCCUPANT MAY NOT BE PROPERLY RESTRAINED.

Corrective Action: DEALERS WILL REPLACE THE DOOR LATCH SWITCH.


NHTSA Recall ID: 97V063001

Mitsubishi MIRAGE 1992 (92)

Mitsubishi Recall Campaign No.:

Component: LATCHES/LOCKS/LINKAGES:DOORS:LATCH

Recall Date (Y/M):1997/05

Defect: EXCESS LUBRICATION CAN CAUSE THE RUBBER DOOR LATCH SWITCH COVER TO DEFORM, AND THE DOOR LATCH SWITCH TO MALFUNCTION, SO THAT THE SHOULDER BELT ANCHORAGE WOULD REMAIN AT THE A-PILLAR WHEN THE DOOR WAS CLOSED.

Consequence: IN THE EVENT OF A CRASH, THE SEAT OCCUPANT MAY NOT BE PROPERLY RESTRAINED.

Corrective Action: DEALERS WILL REPLACE THE DOOR LATCH SWITCH.


NHTSA Recall ID: 95V103004

Mitsubishi MIRAGE 1991 (91)

Mitsubishi Recall Campaign No.:

Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY

Recall Date (Y/M):1995/05

Defect: THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.

Consequence: THE SAFETY BELTS WOULD NOT PROVIDE ADEQUATE PROTECTION TO AN OCCUPANT IN A VEHICLE CRASH.

Corrective Action: OWNERS SHOULD PROMPTLY CHECK THE CONDITION AND OPERATION OF BOTH FRONT SAFETY BELT BUCKLES AND CAREFULLY INSPECT THE RED RELEASE BUTTON FOR ANY BREAKS OR CRACKS. THEY SHOULD ENSURE THAT BOTH BUCKLES ARE OPERATING PROPERLY BY INSERTING EACH LATCH PLATE INTO ITS BUCKLE, TUGGING ON THE BELT TO MAKE SURE THE LATCH IS SECURELY LOCKED, AND THEN PRESSING THE RELEASE BUTTON. THE LATCH PLATE SHOULD POP OUT OF THE BUCKLE WHEN THE BUTTON IS PRESSED. IF EITHER RELEASE BUTTON SHOWS A SIGN OF BREAKING OR CRACKING OR IF EITHER BUCKLE FAILS TO OPERATE PROPERLY, OWNERS SHOULD PROMPTLY CONTACT THEIR AUTHORIZED DEALER TO SCHEDULE AN APPOINTMENT TO HAVE THE BUCKLE REPLACED OR REPAIRED, FREE OF CHARGE. THE MANUFACTURER IS DEVELOPING A REMEDY DESIGNED TO PREVENT FAILURE OF THE BUTTONS THAT ARE NOT CURRENTLY BROKEN.


NHTSA Recall ID: 95V103004

Mitsubishi MIRAGE 1990 (90)

Mitsubishi Recall Campaign No.:

Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY

Recall Date (Y/M):1995/05

Defect: THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.

Consequence: THE SAFETY BELTS WOULD NOT PROVIDE ADEQUATE PROTECTION TO AN OCCUPANT IN A VEHICLE CRASH.

Corrective Action: OWNERS SHOULD PROMPTLY CHECK THE CONDITION AND OPERATION OF BOTH FRONT SAFETY BELT BUCKLES AND CAREFULLY INSPECT THE RED RELEASE BUTTON FOR ANY BREAKS OR CRACKS. THEY SHOULD ENSURE THAT BOTH BUCKLES ARE OPERATING PROPERLY BY INSERTING EACH LATCH PLATE INTO ITS BUCKLE, TUGGING ON THE BELT TO MAKE SURE THE LATCH IS SECURELY LOCKED, AND THEN PRESSING THE RELEASE BUTTON. THE LATCH PLATE SHOULD POP OUT OF THE BUCKLE WHEN THE BUTTON IS PRESSED. IF EITHER RELEASE BUTTON SHOWS A SIGN OF BREAKING OR CRACKING OR IF EITHER BUCKLE FAILS TO OPERATE PROPERLY, OWNERS SHOULD PROMPTLY CONTACT THEIR AUTHORIZED DEALER TO SCHEDULE AN APPOINTMENT TO HAVE THE BUCKLE REPLACED OR REPAIRED, FREE OF CHARGE. THE MANUFACTURER IS DEVELOPING A REMEDY DESIGNED TO PREVENT FAILURE OF THE BUTTONS THAT ARE NOT CURRENTLY BROKEN.


NHTSA Recall ID: 95V103004

Mitsubishi MIRAGE 1989 (89)

Mitsubishi Recall Campaign No.:

Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY

Recall Date (Y/M):1995/05

Defect: THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.

Consequence: THE SAFETY BELTS WOULD NOT PROVIDE ADEQUATE PROTECTION TO AN OCCUPANT IN A VEHICLE CRASH.

Corrective Action: OWNERS SHOULD PROMPTLY CHECK THE CONDITION AND OPERATION OF BOTH FRONT SAFETY BELT BUCKLES AND CAREFULLY INSPECT THE RED RELEASE BUTTON FOR ANY BREAKS OR CRACKS. THEY SHOULD ENSURE THAT BOTH BUCKLES ARE OPERATING PROPERLY BY INSERTING EACH LATCH PLATE INTO ITS BUCKLE, TUGGING ON THE BELT TO MAKE SURE THE LATCH IS SECURELY LOCKED, AND THEN PRESSING THE RELEASE BUTTON. THE LATCH PLATE SHOULD POP OUT OF THE BUCKLE WHEN THE BUTTON IS PRESSED. IF EITHER RELEASE BUTTON SHOWS A SIGN OF BREAKING OR CRACKING OR IF EITHER BUCKLE FAILS TO OPERATE PROPERLY, OWNERS SHOULD PROMPTLY CONTACT THEIR AUTHORIZED DEALER TO SCHEDULE AN APPOINTMENT TO HAVE THE BUCKLE REPLACED OR REPAIRED, FREE OF CHARGE. THE MANUFACTURER IS DEVELOPING A REMEDY DESIGNED TO PREVENT FAILURE OF THE BUTTONS THAT ARE NOT CURRENTLY BROKEN.


NHTSA Recall ID: 95V103004

Mitsubishi MIRAGE 1988 (88)

Mitsubishi Recall Campaign No.:

Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY

Recall Date (Y/M):1995/05

Defect: THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.

Consequence: THE SAFETY BELTS WOULD NOT PROVIDE ADEQUATE PROTECTION TO AN OCCUPANT IN A VEHICLE CRASH.

Corrective Action: OWNERS SHOULD PROMPTLY CHECK THE CONDITION AND OPERATION OF BOTH FRONT SAFETY BELT BUCKLES AND CAREFULLY INSPECT THE RED RELEASE BUTTON FOR ANY BREAKS OR CRACKS. THEY SHOULD ENSURE THAT BOTH BUCKLES ARE OPERATING PROPERLY BY INSERTING EACH LATCH PLATE INTO ITS BUCKLE, TUGGING ON THE BELT TO MAKE SURE THE LATCH IS SECURELY LOCKED, AND THEN PRESSING THE RELEASE BUTTON. THE LATCH PLATE SHOULD POP OUT OF THE BUCKLE WHEN THE BUTTON IS PRESSED. IF EITHER RELEASE BUTTON SHOWS A SIGN OF BREAKING OR CRACKING OR IF EITHER BUCKLE FAILS TO OPERATE PROPERLY, OWNERS SHOULD PROMPTLY CONTACT THEIR AUTHORIZED DEALER TO SCHEDULE AN APPOINTMENT TO HAVE THE BUCKLE REPLACED OR REPAIRED, FREE OF CHARGE. THE MANUFACTURER IS DEVELOPING A REMEDY DESIGNED TO PREVENT FAILURE OF THE BUTTONS THAT ARE NOT CURRENTLY BROKEN.


NHTSA Recall ID: 95V103004

Mitsubishi MIRAGE 1987 (87)

Mitsubishi Recall Campaign No.:

Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY

Recall Date (Y/M):1995/05

Defect: THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.

Consequence: THE SAFETY BELTS WOULD NOT PROVIDE ADEQUATE PROTECTION TO AN OCCUPANT IN A VEHICLE CRASH.

Corrective Action: OWNERS SHOULD PROMPTLY CHECK THE CONDITION AND OPERATION OF BOTH FRONT SAFETY BELT BUCKLES AND CAREFULLY INSPECT THE RED RELEASE BUTTON FOR ANY BREAKS OR CRACKS. THEY SHOULD ENSURE THAT BOTH BUCKLES ARE OPERATING PROPERLY BY INSERTING EACH LATCH PLATE INTO ITS BUCKLE, TUGGING ON THE BELT TO MAKE SURE THE LATCH IS SECURELY LOCKED, AND THEN PRESSING THE RELEASE BUTTON. THE LATCH PLATE SHOULD POP OUT OF THE BUCKLE WHEN THE BUTTON IS PRESSED. IF EITHER RELEASE BUTTON SHOWS A SIGN OF BREAKING OR CRACKING OR IF EITHER BUCKLE FAILS TO OPERATE PROPERLY, OWNERS SHOULD PROMPTLY CONTACT THEIR AUTHORIZED DEALER TO SCHEDULE AN APPOINTMENT TO HAVE THE BUCKLE REPLACED OR REPAIRED, FREE OF CHARGE. THE MANUFACTURER IS DEVELOPING A REMEDY DESIGNED TO PREVENT FAILURE OF THE BUTTONS THAT ARE NOT CURRENTLY BROKEN.


NHTSA Recall ID: 95V103004

Mitsubishi MIRAGE 1986 (86)

Mitsubishi Recall Campaign No.:

Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY

Recall Date (Y/M):1995/05

Defect: THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.

Consequence: THE SAFETY BELTS WOULD NOT PROVIDE ADEQUATE PROTECTION TO AN OCCUPANT IN A VEHICLE CRASH.

Corrective Action: OWNERS SHOULD PROMPTLY CHECK THE CONDITION AND OPERATION OF BOTH FRONT SAFETY BELT BUCKLES AND CAREFULLY INSPECT THE RED RELEASE BUTTON FOR ANY BREAKS OR CRACKS. THEY SHOULD ENSURE THAT BOTH BUCKLES ARE OPERATING PROPERLY BY INSERTING EACH LATCH PLATE INTO ITS BUCKLE, TUGGING ON THE BELT TO MAKE SURE THE LATCH IS SECURELY LOCKED, AND THEN PRESSING THE RELEASE BUTTON. THE LATCH PLATE SHOULD POP OUT OF THE BUCKLE WHEN THE BUTTON IS PRESSED. IF EITHER RELEASE BUTTON SHOWS A SIGN OF BREAKING OR CRACKING OR IF EITHER BUCKLE FAILS TO OPERATE PROPERLY, OWNERS SHOULD PROMPTLY CONTACT THEIR AUTHORIZED DEALER TO SCHEDULE AN APPOINTMENT TO HAVE THE BUCKLE REPLACED OR REPAIRED, FREE OF CHARGE. THE MANUFACTURER IS DEVELOPING A REMEDY DESIGNED TO PREVENT FAILURE OF THE BUTTONS THAT ARE NOT CURRENTLY BROKEN.


TOS + Privacy + Copyrights + Sitemap
Kamal Sinha - www.mitsubishisucks.com

(Last Updated: August 27, 2004.)

Mirage


A Mitsubishi - Eclipse of Ethics presentation.